FL numbers for boat by
North Graphics... www.northgraphics.com
Date: 06/02/06
before paint..
Date: 06/02/06
carbon fiber reinforcement
Date: 06/02/06
another shot of filled fuel fill hole
Date: 06/02/06
rear shot of 2" one way valve
Date: 06/02/06
another shot of footstrap mounting hardware
Date: 06/02/06
2"ID "Lowes" one-way valve entrance hole inside hull epoxied into the hull
Date: 06/02/06
Dakine Footstraps from Wind Surf Shop
Date: 06/02/06
showing the thickness
Date: 06/02/06
25mm Hydro Turf underpadding w/ backing tape
Date/Time: 1999:05:14 23:35:00
filled the fuel fill hole w/ fiberglass then filled w/ Rage body filler to shape
Date/Time: 1999:05:14 23:39:03
top view of gooped nuts
Date: 06/02/06
shown gooped up
Date: 06/02/06
acorn nut and 1" flatwasher
Date: 06/02/06
shown how the will ber welded
Date: 06/02/06
after clear....
Date/Time: 1999:05:18 23:54:37
SS nuts w/ washers epoxied to tray for footstraps
Date/Time: 1999:05:15 02:56:44
after paint before decals....
Date/Time: 1999:05:19 18:34:11
Watercraft Factory footholds
Date/Time: 1999:05:19 21:24:01
Hydro Turf Diamond Cut padding w/ Dakine front footstrap
Date/Time: 1999:05:28 02:06:52
Pole painted by Daylite Ramsey (Daylite69) on PWCToday.com
Date/Time: 1999:05:28 02:07:48
X-Metal Bracket w/ Pole and breather system
Date/Time: 1999:05:28 02:07:13
surf stance for surf riding tricks...
Date/Time: 1999:05:28 02:14:16
shot of Watercraft Factory foothold
Date/Time: 1999:05:28 02:09:15
mounted steering cable on X-Metal pole
Date/Time: 1999:06:01 22:33:00
underside of pole tapped w/ 1/4"-20 tap for UMI steering post and X-Metal shortened turnplate... and bars...
Date/Time: 1999:06:02 00:14:57
close up of X-Metal steering setup..
www.xmetalworks.com
Date/Time: 1999:06:01 23:34:34
Solas 12/15 w/ 3mm cutback
Work 201 Intake grate
Stock Rideplate
Date/Time: 1999:06:02 00:50:50
pre turfing fitting of pole pad
Date/Time: 1999:06:02 00:51:26
fitting and modding Watercraft Factory chin/pole pad to fit my pole the way I like it
Date/Time: 1999:06:02 00:51:31
added gasket material to lip of hood to create a better seal w/ the top deck
Date/Time: 1999:06:02 01:28:18
hood shown w/ mounting hardware
Date/Time: 1999:06:02 01:04:03
Custom made Hydro turf pole cushion to prevent pole from slamming down and cracking hood
Date: 06/02/06
another shot of finished pole steering system and pole pad
Date: 06/02/06
steering done and pole pad mounted
Date: 06/02/06
the strap, limiting rope
Date: 06/02/06
monting point for front of strap... nice beefy location
Date: 06/02/06
more sexiness
Date: 06/02/06
sexy.... as Jerry put it
Date: 06/02/06
showing the length of a -4 pole w/ -2.5" turnplate on a Watercraft Factory hood
Date/Time: 1999:06:02 22:38:13
top of crank case before boring out to 90.5mm to accept the larger bore of the 760cc cyl.
Date/Time: 1999:06:06 01:09:25
tray area w/ uni-strap going down the middle of hood then bolted to firewall. Also tow rope and pole limiting rope
Date/Time: 1999:06:02 22:39:18
pic showing the location you will need to fill w/ epoxy to reinforce the area that gets removed on the other side when boring
Date/Time: 1999:06:17 16:55:26
Jr. Maggo www.jrmagoos.com porting and big bore kit (84mm)
Date/Time: 1999:06:17 16:55:42
modded fuel tank for internal fuel fill
Date/Time: 1999:06:17 16:56:07
engine compartment showing Joe Kenney Keepers www.blowsion.com and motor mounts
Date/Time: 1999:06:17 16:56:21
another shot of the same.....
Date/Time: 1999:06:17 16:56:42
Jr. Magoo cyl. w/ dual 44mm Mikuni carbs before head install
Date/Time: 1999:06:17 19:24:35
carb side shot of motor
Date/Time: 1999:06:18 00:21:04
another shot
Date/Time: 1999:06:19 02:10:03
motor w/ girdled head
Date/Time: 1999:06:19 02:11:20
color coordinated...... bitch
Date/Time: 1999:06:24 00:41:17
DCP 0752
Date/Time: 1999:06:24 00:45:32
poofy nose padding...
Date: 06/02/06
Full Frontal Nudity
Date: 06/02/06
side sponson install (tubbie 2)s
this view shows the location of sponson as directed by www.Blowsion.com
Date: 06/02/06
grinding the paint/primer to bare SMC.. then re-draw sponson to sanded side of hull
Date: 06/02/06
adding fiber matte to the inside of the tubbie to act as re-inforcement and to adhear the sponson to the hull better
Date: 06/02/06
soaking resin into foam and matte for maximum stickage..
Date: 06/02/06
DCP_0823
Date/Time: 1999:12:19 11:11:52
DCP_0824
Date/Time: 1999:12:19 11:12:01
DCP_0826
Date/Time: 1999:12:19 11:12:16
000bb703d296
Date: 05/03/07
3ec0d2ffc4a1
Date: 05/03/07
05-02-07_1943
Date: 05/03/07
6ce76bd0b26f
Date: 05/03/07
369a90dec21a
Date: 05/03/07
0546c46c1e9c
Date: 05/03/07
dbda9469a85f
Date: 05/03/07
edc3647141cc
Date: 05/03/07
